Xylem IM112 AquaBoost 1AB1 & 2AB1 Variable Speed Pum Bedienungsanleitung Seite 5
- Seite / 40
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
5
Step 1 – Pump / AquaBoost
Installation
1) Refer to the pump manual for instructions
on proper installation of the pump.
2) Mount the AquaBoost Controller on a wall in
a well-ventilated area.
3) Pressure Transducer Installation: Locate
the pressure transducer and cable. The
threaded end of the transducer is 1/4" NPT.
Install the transducer in the tee or on the
downstream side of the check valve or foot
valve.
4) Connections in the Conduit Box: (when
using controller with other pumps) The
free end of the motor cable should now be
routed through the strain relief on the
conduit box. Connect the motor leads using
the motor nameplate as a reference. Place
the thermistor terminal in the conduit box
and fasten so that the sensor will contact
the motor shell. Note: Step 4 is completed
at the factory for complete AquaBoost pump
kits with pumps.
5) Input Power Cable Installation: The cable
has been pre-wired to the AquaBoost
Controller. Cut the loose end to length, strip
the wires and install the appropriate mating
connector or wire directly to a junction box
or distribution panel providing 208-230V,
single phase power. An all leg disconnect
switch should be provided. Follow local
electrical codes and NEC.
Installation Procedures
Diagram 4
3/8” NPT
AUX. POWER
1/2”
NPT
INPUT
POWER
CORD
1/2”
NPT
OUTPUT
POWER
CORD
3/8” NPT
TRANSDUCER
PORT
4.38
0.19
2 PLS
0.63
2 PLS
4.38
0.19
2 PLS
0.41
2 PLS
6.188
BACK VIEW AQUABOOST MOUNTING
6.00
0.25
0.78
7.25
0.38
2 THRU HOLES
Ø .63
3 THRU HOLES
Ø .47
2 THRU HOLES
Ø .87
Diagram 3
1AB1
2AB1 and 3AB1
- Goulds Pumps 1
- System Design 3
- Safety Instructions 4
- Step 1 – Pump / AquaBoost 5
- Installation Procedures 5
- Installation Confi guration 6
- Connection / Wiring Diagrams 8
- Input/Output P ower Wiring 8
- Control Wiring 8
- Pump Priming 9
- Run Test 9
- Operator Displays 10
- Error Signals 10
- Appendix A 11
- Pressure Transducer 11
- Appendix B 12
- Engineered for life 13
- Bombas Goulds 14
- Diseño del sistema 16
- Instrucciones de seguridad 17
- Procedimientos de instalación 18
- AquaBoost I 21
- Cebado de la bomba 22
- Prueba de funcionamiento 22
- Indicaciones para el operador 23
- Señales de errores 23
- Apéndice A 24
- Transductor de presión 24
- Apéndice B 25
- AquaBoost 25
- Systèmes types 29
- Consignes de sécurité 30
- Installation 31
- III Raccordement électrique 32
- II Montage type 32
- Schémas de câblage 34
- Entrée et sortie de courant 34
- Bornes de commande 34
- IV Amorçage de la pompe 35
- V Essai de fonctionnement 35
- Messages affi chés 36
- Signaux d’erreur 36
- EMBOUT FILETÉ DE 1/4 po, NPT 37
- Sortie (+ 0,5 V à 37
- + 4,5 V) 37
- + 5 V (CC*) 37
- Notes — Notas 39
Verwandte Produkte und Handbücher für Pumpen Xylem IM112 AquaBoost 1AB1 & 2AB1 Variable Speed Pum
(24 Seiten)
(72 Seiten)
(16 Seiten)Mittler-bros-machine-tool 1200 manuales
Manuales del propietario y guías del usuario para Equipos De Agua Mittler-bros-machine-tool 1200.
Ofrecemos 1 manuales en pdf Mittler-bros-machine-tool 1200 para descargar gratis por tipos de documentos: Manual de usuario
Kommentare zu diesen Handbüchern